🔎 Disclosure: Heads up, babe: some links here are affiliate links, which means you might throw a tiny commission my way if you buy (zero extra cost to you). Only things you’d actually use and love get shared on this site.
Imagine finally:
- Pouring a smoothie that does not taste like old residue
- Blending once without seeing stuck buildup around the blade
- Keeping the jar clear longer and avoiding early replacement
Here’s how you start…
1. Unplug The Blender Before Cleaning
Water near the base can cause damage fast.
Start Small With This: Unplug the blender and separate the jar from the base before adding water.
2. Rinse The Jar With Warm Water Right After Use
Dried smoothie bits harden within minutes.
Here’s What To Do: Rinse the jar with warm water as soon as you finish blending.
3. Fill The Jar Halfway With Warm Soapy Water
Soap loosens sticky fruit and nut butter fast.
Begin With This: Add warm water and a few drops of dish soap to the jar until it is halfway full.
It will be so much easier if you use a soft nonstick safe scrub sponge to clean without scratching the inside.
4. Run The Blender For 30 Seconds To Loosen Residue
Spinning water reaches under the blade where hands cannot fit.
Give This A Try: Place the jar back on the base and blend the soapy water for 30 seconds.
5. Scrub Around The Blade With A Long Brush
Food gets trapped right under the blade edges.
Instead, Try This: Use a long handled brush to scrub gently around the blade base.
This gets easier if you use a long handle bottle cleaning brush to reach the bottom safely.
6. Remove The Gasket Ring And Wash It Separately
The rubber ring traps smells if left dirty.
The Easy First Step Is: Twist off the blade assembly and remove the gasket to wash it in warm water.
7. Soak The Jar For Ten Minutes To Lift Dried Bits
Old protein powder leaves a cloudy film.
One Thing That Helps Is: Let the jar sit filled with warm soapy water for 10 minutes before scrubbing.
8. Use Baking Soda On Cloudy Spots
Cloudy marks form from mineral deposits and residue.
To Avoid Feeling Overwhelmed: Sprinkle baking soda on a damp sponge and rub lightly in circles.
9. Clean The Lid And Center Cap With Warm Soapy Water
Smoothie splashes collect under the cap.
Start This Way: Separate the lid and cap and wash both pieces fully in warm water.
10. Wipe The Base With A Damp Cloth
Spills drip down the sides during pouring.
Here’s A Gentle Way To Start: Use a slightly damp cloth and wipe around the base and buttons carefully.
11. Clean Around The Buttons With A Cotton Swab
Sticky edges collect dried juice and dust.
Here’s A Small Step That Helps: Dip a cotton swab in warm water and run it along the seams.
12. Dry All Parts Fully Before Reassembling
Trapped moisture leads to stale smells.
The Most Doable Way Is: Lay each piece on a towel until it feels completely dry.
13. Check Under The Blade For Trapped Food
Small seeds often hide under the blade edge.
Consider This: Look closely under the blade and brush out any stuck bits.
14. Avoid Submerging The Blender Base In Water
The motor area is not made for soaking.
The Easier Approach Is: Keep the base dry and only wipe it with a damp cloth.
15. Polish The Outside With A Dry Microfiber Cloth
Fingerprints and smudges dull the shine.
Here’s The Shortcut Version: Buff the outside shell with a dry microfiber cloth for a clean finish.
16. Leave The Jar Open To Air Dry
Closing the lid too soon traps moisture inside.
Start By Doing This Instead: Let the jar sit open on the counter for at least 30 minutes.
17. Repeat Deep Cleaning Every Week To Prevent Buildup
Waiting too long makes residue harder to remove.
One Easy Reset Is: Add a weekly reminder so the blender never smells stale again.
📌 SAVE IT FOR LATER! 📌
